Peugeot 208 Key Replacement
Peugeot 208 key replacement is best left to professional auto locksmiths who have the proper tools and know-how. They will be able to create and program new keys quicker than a dealership and at a cheaper cost.
If your key fob has stopped locking or unlocking your doors, it is likely due to a dead battery in the coin. However, there are many other reasons that the key may be malfunctioning.
Dead Coin Battery
A dead coin battery will stop your Peugeot 208 from locking and unlocking, as well as hindering it from starting the engine. If this is the case, you'll need to use the backup starting method that is detailed in the owner's manual of your vehicle.
The spark plugs might also be worn out. Spark plugs are what ignite the fuel to start the engine. However they are limited in their lifespan. If they aren't used enough, they will eventually fail.
There is a simple solution to this issue. The best thing to do is to determine the voltage of your car battery with a multimeter. If peugeot partner key fob 's less than 11.5 Volts it is time to replace it. If the battery is damaged it is necessary to clean its contacts. This can be accomplished by removing the rubber cover from the two terminals of the battery, and then using a wirebrush to clean any corroded parts of the battery. Then, you should connect the cables for the positive and negative poles.
Water Damage
If your 208 doesn't start and the battery hasn't gone flat, you should inspect the spark plugs. You may find that they are simply too dirty and they don't spark. The spark plugs can be cleaned in the workshop.
Peugeot cars use a key with a transponder compatible with the immobiliser. This ensures that only the right key is able to turn the engine. If the chip inside the Peugeot key is damaged, it won't transmit the proper signal to the vehicle.
This is a frequent issue that can be caused by water damage. This is especially prevalent in colder climates, as the vehicle may have been exposed to rain or snow. In this case, contact an experienced locksmith who has the required tools and equipment to modify the key. They will also have the latest technology and machinery required to make the Peugeot smart key. The process shouldn't be more than 15 minutes.
Contacts for the battery that are defective
Peugeot replaced the old transponder chips with a brand new model that is based on electronic components mounted on a circuit board. The new system works great in its initial state, but the circuit boards deteriorate over time and stop working properly.
This can prevent the immobiliser chip from triggering the immobiliser chip, causing your car not to start. Contact a Peugeot specialist or a locksmith, if this is the situation.
Another issue that is common is when the battery in the key fob starts to die, this causes the key blade to stop from entering the lock. A locksmith in your car will replace the battery and then cut a new blade for you. This is a quick solution.
Faulty Receiver Module
If your Peugeot key fob stopped working after dropping it on the ground, being exposed to a sudden rain or accidently washing it the wrong way, it could be due to a faulty receiver module. The receiver is responsible for transmitting radio frequency signals to the onboard computer, which is responsible for controlling the centralized locking system in your Peugeot vehicle.
The rubber seals on the key fob prevent water from reaching the electronic chip. However, prolonged exposure to water may break through these seals, causing damage to the chip. The high salt content of the ocean or pool could cause damage to the key fob when it is submerged.
The module must be replaced if your Peugeot spare key is no longer working. This is only performed by a professional auto locksmith or Peugeot specialist. Peugeot keys unlike other automobiles, are protected by an immobilizer system. This requires the correct coding to start the car. This is why you must go with a knowledgeable Peugeot locksmith for the job of designing and programming an alternative.
Computer with a problem on board
The on-board computer inside your Peugeot is responsible for a number of the systems within your car, ranging from power windows to the airbags. When something goes wrong in these systems, it will usually show a code that identifies the problem. This code is stored in the system and will stay there until the problem is solved. Often, this will involve replacing the computer on board.
The most common cause of the airbag warning light to turn on is corrosion or loose connections within the sensor. This could be due to wear and tear, aging, exposure to moisture and salt. It is crucial to get this issue addressed as soon as possible, as an airbag that is malfunctioning can be risky in the event of an accident.
If you see a card not found error on your Peugeot, the key battery inside the key fob could be weak or dead. This will stop the key fob sending a signal to deactivate your vehicle's immobilizer. You can test this by pressing the unlock button on the key fob and then attempting to start your vehicle. If this fails then the battery in the key will need replacing.